Woven Field Fence in Woods for Nigerian Dwarfs

OneFineAcre

Herd Master
Joined
Dec 28, 2012
Messages
9,139
Reaction score
10,265
Points
633
Location
Zebulon, NC
@Goat Whisperer

No. If I had to install all of that fencing we would have never been able to move. :)

I hired a contractor to do the initial fencing. I did have to cut the path for the fence.

We will be doing more eventually which I will do myself since it will be in smaller chunks.
 

OneFineAcre

Herd Master
Joined
Dec 28, 2012
Messages
9,139
Reaction score
10,265
Points
633
Location
Zebulon, NC
This is the area I fenced, sections 1 and 2. Bucks are in 2, does in 1.
3728 Rosinburg Marked 2.jpg


The earlier pictures through the woods start on the left side behind the building, go across the back and there are a couple of the section in the middle

Picture in front of 2 standing in the area not fenced.
Buck Pen.jpg


Front of section 1.

photo 1 (9).jpg
 
Last edited:

Baymule

Herd Master
Joined
Aug 22, 2010
Messages
33,470
Reaction score
100,481
Points
873
Location
East Texas
Oh, and then there is the lusting over a big pile of gravel!
How did you know??? :lol: We just bought a new place, fixing up, painting, getting carport in 2 weeks, have to build fence.......and there is deep sand at the end of the driveway by the road. When it rains, it is slush. Diesel truck + deep sand = stuck. The rocks we want are not the diamond kind-they are the gray/brown/large chunky kind--and LOTS of them!!
 

greybeard

Herd Master
Joined
Oct 23, 2011
Messages
5,940
Reaction score
10,803
Points
553
Location
East Texas
Great looking fence OneFineAcre. A few things.

I too have built fence thru woods, and like the fence in the pictures, it's straight as an arrow since it is on a property line & I did it myself, but it's not woven wire. My brother & I did the woven wire (what we called hog wire, with 2 strands of barbed on top) thing on this place before it was cleared off when I was 16--1966 and it went ok, but it was nothing but work.

For my fences, instead of stringing a line as in the pictures, I just started clearing one tree at a time, until I could stand at the start point on one end, then sight down thru the woods with my rifle scope till I could see the end point 2250' away. (I put a t-post in at the end with a reflector on it) Then, I set my big posts on each end and unrolled one strand of HT 12ga wire, stretched it tight as a banjo string and that guaranteed a straight fence. A crooked fence places stress on posts and is not as attractive as a straight one. Along that stretched wire, I planted a post just every 100' or so to hold the wire up, then unrolled and stretched all the rest of my wire. I added all the other post after I had all the wire up--but again, that isn't woven wire--it's HT and barbed wire.

Using trees for posts--the only way I will do it is to nail a treated 2x6 to the tree then staple the wire to the board. Otherwise, the tree's bark will grow into and around the wire and if the wire ever gets loose or damaged, there is no way to easily retighten and repair it without a LOT of cutting and splicing. The original fence I talked about from the 60s was stapled to trees, and lordy what a pita it was to remove when I rebuilt it.

Sand driveway. Part of mine is and it can get messy. In East Texas, gravel is just cost prohibitive because it is in such high demand from the concrete industry. (I live 45 miles North of Houston)
The options are crushed concrete--trucked in limestone--washout from ready mix concrete plants, and iron ore. I used iron ore, as it is readily available and inexpensive. Don't remember how many yards³ I bought but it was 8 dump truck loads for about $1500 in 2011. There is a "using curve" to iron ore. Spread it, level it, pack it down by driving over it fully several times then wait for the first good soaking rain. It will turn into a gawd awful mess, as the rain settles it down, but within a day or two, it is solid enough for an 18 wheeler to traverse and forever afterwards will be solid. It's just that first time it rains that is messy. The longer it is in place, the more the iron particles rust together and the better it becomes.

In small patches of loose sand, I have seen (and had good luck myself), just buying bags of sackrete, ($4/80lbs) dumping them on the sand, spread it out, and tilling the sackrete into the sand with a garden tiller or big tiller behind a tractor, then either wet it down good or wait for a rain. Don't drive on it till it sets up. Do NOT use plain portland cement for this. That makes what is known as stabilized sand. It works good for a base under culverts or for a seldom used drive with something else laid over it, but driving directly on stabilized sand every day will soon turn it right back into powdery sand. (If you do the sackrete/tilling thing, immediately afterwards wash the tiller good with a garden hose and pressure nozzle--cement is corrosive and will turn your tiller to rust if not washed off)
 

Baymule

Herd Master
Joined
Aug 22, 2010
Messages
33,470
Reaction score
100,481
Points
873
Location
East Texas
@greybeard that is a great idea for the sandy driveway. There's lots of iron ore in the Tyler area and I bet I can get some at a fairly decent price. Thanks for the info!
 

upsidedown

Chillin' with the herd
Joined
Apr 16, 2013
Messages
12
Reaction score
4
Points
26
nice looking fences!! That is on my to do list this spring :)
 

babsbag

Herd Master
Joined
May 10, 2010
Messages
7,886
Reaction score
9,317
Points
593
Location
Anderson, CA
I live on probably the hilliest and rockiest land in all of CA. I DO use trees for fence posts, but I am OLD and won't be here long enough to watch the trees die and fall down. They are oak trees and even if they do die it could years and years and years before they fall over. Some of the oaks that are dead make the best posts; they are incredibly hard. I don't nail to the trees, I use wire wrapped around the trunk. If I had to cut trees in order to fence the stumps would still be in the way so I just put the trees to use.

I use woven 2x4 no climb wire; it does hills and valleys better than welded. When the dip in the ground is severe I will put a post in the middle of the dip and cut the fencing at the post, overlap it and start up the hill; some dips are just too big to stretch through. I use the steel t-posts about every 8-10 feet and if there are no trees I use a peeler core in concrete about every 100' or so, but I have lots of trees so really not an issue. I also use trees to stretch the fence, they make a great dead man anchor. :) When I do have to deal with a severe dip I put a peeler core in concrete in the "valley" so I can stretch from it. I am a stickler for a tight fence.
 
Top